Changes

Before we could run through all bundles through QA tests, we had to calibrate and standardize the QA testing procedure. We found the following sources of error:

Before we could run through all bundles through QA tests, we had to calibrate and standardize the QA testing procedure. We found the following sources of error:

*'''Laser Intensity''' - if the laser is brighter, each fiber will result in a higher photon yield. Dr. Jones has compensated for this. We also found that the photon yields decrease as the pulser's 9V battery is drained.

*'''Laser Intensity''' - if the laser is brighter, each fiber will result in a higher photon yield. Dr. Jones has compensated for this. We also found that the photon yields decrease as the pulser's 9V battery is drained.

*'''Temperature of the SiPM board/Time Between Runs''' - we found that as the fiber runs were done repeatedly without turning off the electronics and removing the board, the photon yield decreases. Dr. Jones ran a script which automated the run process so that the runs had a certain amount of time in between. This histogram was made of 255 runs at approximately the same temperature (same time between runs) and compares each photon yield to the average over all runs.

*'''Temperature of the SiPM board/Time Between Runs''' - we found that as the fiber runs were done repeatedly without turning off the electronics and removing the board, the photon yield decreases. Dr. Jones ran a script which automated the run process so that the runs began at the beginning of each hour. This histogram was made of 15 runs of 15 fibers (resulting in 255 data points) at approximately the same temperature (same time between runs) and compares each photon yield to the average over all runs. The standard deviation of any given ratio was 0.03

[[File:LH_prelimfibertests_temp.png|thumb|center|A histogram of the ratio of photon yields from each fiber compared to the average. This includes 225 data points.]]

[[File:LH_prelimfibertests_temp.png|thumb|center|A histogram of the ratio of photon yields from each fiber compared to the average. This includes 225 data points.]]

*'''Depth of the fibers in the chimney''' - We found that differences as small as 0.5 mm can have a minor affect on the photon yields. These histograms show the ratio of photon yields after a 0.5 mm or 1.0 mm fiber retraction to the photon yield while flush.

 

*'''Depth of the fibers in the chimney''' - We found that differences as small as 0.5 mm can have a minor affect on the photon yields. These histograms show the ratio of photon yields after a 0.5 mm or 1.0 mm fiber retraction to the photon yield while flush. The mean ratio for the 0.5 mm test was 0.95 with a standard deviation of 0.05 and the mean ratio for the 1.0 mm experiment was 0.88 with a standard deviation of 0.8

{|style="margin: 0 auto;"

{|style="margin: 0 auto;"

| [[File:LH_prelimfibertests_halfmm.png|thumb|center|A histogram of the ratio of photon yields from a fiber who was retracted 0.5 mm into the chimney compared to the a flush fiber. This includes 15 data points.]]

| [[File:LH_prelimfibertests_halfmm.png|thumb|center|A histogram of the ratio of photon yields from a fiber who was retracted 0.5 mm into the chimney compared to the a flush fiber. This includes 15 data points.]]

| [[File:LH_prelimfibertests_mm.png|thumb|center|A histogram of the ratio of photon yields from a fiber who was retracted 1.0 mm into the chimney compared to the a flush fiber. This includes 15 data points.]]

| [[File:LH_prelimfibertests_mm.png|thumb|center|A histogram of the ratio of photon yields from a fiber who was retracted 1.0 mm into the chimney compared to the a flush fiber. This includes 15 data points.]]

|}

|}

*'''Overall Environmental Factors''' - I did a series of runs where between each run, I'd turn off the electronics, remove the SiPM board, remove the fibers and replace the fibers so they're flush. Here you can see the overall variation between a bunch of runs. All of this variation is variation we will be present when we do the actual runs.  

*'''Overall Environmental Factors''' - I did a series of runs where between each run, I'd turn off the electronics, remove the SiPM board, remove the fibers and replace the fibers so they're flush. Here you can see the overall variation between a bunch of runs. All of this variation is variation we will be present when we do the actual runs. The mean ratio was 0.99 with a standard deviation of 0.07

[[File:LH_prelimfibertests_environ.png|thumb|center]]

[[File:LH_prelimfibertests_environ.png|thumb|center]]

*'''Paper Spacers between scintillators'''- I tested the necessity of the paper spacers between the scintillating fibers. This histogram shows the ratios of individual fibers run with paper spacers and without. I believe this is sufficient enough to no longer require paper spacers.

*'''Paper Spacers between scintillators'''- I tested the necessity of the paper spacers between the scintillating fibers. This histogram shows the ratios of individual fibers run with paper spacers and without. This is not all the data, however, three data points were excluded. The ratios were 0.45, 0.43, and 0.74 Because the lack of paper spacing resulting in three catastrophic results, it has been decided that the paper spacing is necessary.  

[[File:LH_prelimfibertests_paper.png|thumb|center]]

[[File:LH_prelimfibertests_paper.png|thumb|center]]