Changes

Jump to navigation Jump to search
Line 21: Line 21:  
This semester, my work focused on the physics-engineering design of the tagger microscope box to be used for the GlueX particle accelerator project in Hall D at Jefferson National Lab in Virginia. The volume of work that I ultimately produced was not as much as I had hoped for, because I spent the first months of the semester learning the computer programs needed to facilitate my design work. Based on my current knowledge of these programs plus the final data and design files I was able to create, I would consider this semester a definite success.
 
This semester, my work focused on the physics-engineering design of the tagger microscope box to be used for the GlueX particle accelerator project in Hall D at Jefferson National Lab in Virginia. The volume of work that I ultimately produced was not as much as I had hoped for, because I spent the first months of the semester learning the computer programs needed to facilitate my design work. Based on my current knowledge of these programs plus the final data and design files I was able to create, I would consider this semester a definite success.
   −
The main computer program used for my project is TurboCad. TurboCad is a drafting program similar to both AutoCAD and Solid Works, but is better suited to my project because it allows more 2D and isometric views, as well as a full repertoire of snaps and rendering settings. The currently-marketed edition of TurboCad is Version 15.0, but for the GlueX design project I was working primarily with Version 12.0. It took some time into the semester until I could properly install it on my personal laptop, but after that time my work became infinitely more efficient.  The TurboCad program was somewhat complicated to learn, but I did so successfully by using the help menus and tutorials, as well as by asking questions at lab meetings and experimenting on my own. The first challenge I gave myself was drafting a [http://zeus.phys.uconn.edu/halld/tagger/fp-prototype/Bicycle_Frame.TCW a bicycle frame] (exactly proportioned to my size), and once I succeeded at this near the end of October, I began working exclusively on the Tagger design. The files I created for the Tagger design still need a lot of revision, which I hope to complete over the winter break and into next semester. Ideally, I would like to have the prototype Tagger box machined and assembled by sometime in February of 2009.
+
The main computer program used for my project is TurboCad. TurboCad is a drafting program similar to both AutoCAD and Solid Works, but is better suited to my project because it allows more 2D and isometric views, as well as a full repertoire of snaps and rendering settings. The currently-marketed edition of TurboCad is Version 15.0, but for the GlueX design project I was working primarily with Version 12.0. It took some time into the semester until I could properly install it on my personal laptop, but after that time my work became infinitely more efficient.  The TurboCad program was somewhat complicated to learn, but I did so successfully by using the help menus and tutorials, as well as by asking questions at lab meetings and experimenting on my own. The first challenge I gave myself was drafting a bicycle frame, and once I succeeded at this near the end of October, I began working exclusively on the Tagger design. The files I created for the Tagger design still need a lot of revision, which I hope to complete over the winter break and into next semester. Ideally, I would like to have the prototype Tagger box machined and assembled by sometime in February of 2009.
    
This semester, I learned that the process of designing the Tagger box is entirely experimental. Overall as a lab group, we have a general idea of how the box should be constructed, although this is subject to slight revisions on a weekly basis. Some of the main revisions integrated into the design this semester include the “skeleton” support structure versus a solid box to reduce weight, and the idea of using foil to form the sides of the box to access the fibers and motors inside. As each of these revisions was discussed and sketched out, it was my job to draft the new design in TurboCad – a process that became a great learning experience for me on many levels.  In this same vein, I would characterize the entire Fall 2008 semester as a “great learning experience” for my design project. The presentable TurboCad files that I have created are indexed below. While they are not many in number, I believe that they accurately represent my growing confidence and comfort level with using the program. The majority of the Tagger’s skeleton is rendered, and I hope to work with our lab group and the Physics machine shop to expand on all of these designs in the coming weeks and months. For this semester, however, I feel that my greatest victory was learning the TurboCad program, which will be an invaluable tool for me to use in the future.
 
This semester, I learned that the process of designing the Tagger box is entirely experimental. Overall as a lab group, we have a general idea of how the box should be constructed, although this is subject to slight revisions on a weekly basis. Some of the main revisions integrated into the design this semester include the “skeleton” support structure versus a solid box to reduce weight, and the idea of using foil to form the sides of the box to access the fibers and motors inside. As each of these revisions was discussed and sketched out, it was my job to draft the new design in TurboCad – a process that became a great learning experience for me on many levels.  In this same vein, I would characterize the entire Fall 2008 semester as a “great learning experience” for my design project. The presentable TurboCad files that I have created are indexed below. While they are not many in number, I believe that they accurately represent my growing confidence and comfort level with using the program. The majority of the Tagger’s skeleton is rendered, and I hope to work with our lab group and the Physics machine shop to expand on all of these designs in the coming weeks and months. For this semester, however, I feel that my greatest victory was learning the TurboCad program, which will be an invaluable tool for me to use in the future.
58

edits

Navigation menu