Difference between revisions of "Characterizing SiPMs"

From UConn PAN
Jump to navigation Jump to search
Line 36: Line 36:
 
Below are the diagrams of the dark box with the HPD and SiPM assemblies installed. A temperature controller system (TE Tech. [http://www.tetech.com/temp/tc24-12.shtml TC-24-12]) was procured, which operates by driving a Peltier junction based on feedback from a thermistor compared to voltage-specified reference temperature. It was [[:media:Tc2412calib.pdf|calibrated]] and installed into the wall of the dark box via a custom-designed light-tight frame.
 
Below are the diagrams of the dark box with the HPD and SiPM assemblies installed. A temperature controller system (TE Tech. [http://www.tetech.com/temp/tc24-12.shtml TC-24-12]) was procured, which operates by driving a Peltier junction based on feedback from a thermistor compared to voltage-specified reference temperature. It was [[:media:Tc2412calib.pdf|calibrated]] and installed into the wall of the dark box via a custom-designed light-tight frame.
  
[[Image:DarkboxDiagram_HPD.png|border|Diagram of the dark box with the HPD module installed. V<sub>HV</sub> = -12 kV, V<sub>b</sub> = 60 V.]]
+
{| border="0"
 
+
|-
[[Image:DarkboxDiagram_SiPM.png|border|Diagram of the dark box with a SiPM mounted on a temperature-controlled cold plate. V<sub>b</sub> is the bias voltage discussed below, V<sub>s</sub> is the preamplifier supply voltage set to 5 V in our work (recommended levels: 4 - 9 V)]]
+
|[[Image:DarkboxDiagram_HPD.png]]
 +
|-
 +
| Diagram of the dark box with the HPD module installed. V<sub>HV</sub> = -12 kV, V<sub>b</sub> = 60 V.
 +
|-
 +
| &nbsp;
 +
|-
 +
| [[Image:DarkboxDiagram_SiPM.png]]
 +
|-
 +
| Diagram of the dark box with a SiPM mounted on a temperature-controlled cold plate. V<sub>b</sub> is the bias voltage discussed below, V<sub>s</sub> is the preamplifier supply voltage set to 5 V in our work (recommended levels: 4 - 9 V)]]
 +
|-
 +
\}
  
 
== SiPM Measurements ==
 
== SiPM Measurements ==

Revision as of 23:20, 10 August 2007

SiPM Performance Requirements

The tagger microscope consists of many identical and well isolated readout channels, each consisting of a several cm long scintillating fiber connected to a clear acrylic fiber light guide. A tagging electron travels axially down the length of a scintillating fiber depositing 4 MeV of energy in the fiber, resulting in 1600 scintillation photons within the forward capture cone of the fiber. Assuming that 80% of these are delivered to the SiPM active surface and a conservative estimate of 15% for the efficiency of the SiPM leads to an estimate of 190 for the average SiPM pixel count per event. Monte Carlo simulations have shown that an efficient detection threshold corresponds to 40% of the average pulse height, or 80 SiPM pixels. This implies a requirement for the dark rate that spontaneous pulses never exceed 80 pixels.

The large photon yield expected at the end of the light guide does not demand unusual detection efficiency on the part of the SiPM. For example, 10% efficiency with the above number of photons still yields a signal of 130 photons. However, given that the scintillator (BCF-20) has a finite decay time (2.7ns) the more photons are produced the more clearly resolved is the time of the pulse.

The device is expected to have a high enough gain (measured in electrons per photon detected) - around 106. in order for such a small light signal to be recorded by conventional electronics. Such devices are also susceptible to spurious, thermally excited pixel breakdowns, each showing up as a single photon hit ("dark count"). High rate of these single-pixel events may create a pileup above the signal threshold. All of the above parameters (detection efficiency, gain and "dark rate") depend on applied bias voltage and temperature. Stability of performance despite expected fluctuations of these variables is an important requirement.

Another criterion in SiPM selection is its dynamic range. Although this readout device essentially provides digital output - scintillation detected or not - enough of a range is necessary to set a threshold above the noise floor and to account for some pixels being not having required from a previous hit .

Bench Test Setup

A wooden dark box was initially constructed for the a hybrid photo-diode (HPD) module. A pulser was installed on the opposite end of the box composed of a fast LED driven by a pulser circuit shown on the right.

A pulser circuit designed to drive the LED for photo-detector bench tests. The circuit differentiates the input signal, thus the amplitude of the input square wave controls pulse amplitude up to the saturation point, at which the pulse shape broadens to a maximum of 6 ns. Vs = 5 V


Running this setup with an HPD of known characteristics allows us to calibrate the light intensity. The SiPM detection efficiency can then be characterized relative to the HPD. The signal from the SiPM was clean enough to distinguish peaks corresponding to discreet photon (pixel) counts in the histogram signal integrals. Therefore, the gain of the SiPM was found independently of the HPD - they were self-calibrating!


Below are the diagrams of the dark box with the HPD and SiPM assemblies installed. A temperature controller system (TE Tech. TC-24-12) was procured, which operates by driving a Peltier junction based on feedback from a thermistor compared to voltage-specified reference temperature. It was calibrated and installed into the wall of the dark box via a custom-designed light-tight frame.

\}

SiPM Measurements

DarkboxDiagram HPD.png
Diagram of the dark box with the HPD module installed. VHV = -12 kV, Vb = 60 V.
 
DarkboxDiagram SiPM.png
Diagram of the dark box with a SiPM mounted on a temperature-controlled cold plate. Vb is the bias voltage discussed below, Vs is the preamplifier supply voltage set to 5 V in our work (recommended levels: 4 - 9 V)]]
Summary of SiPM Properties measured at room temperature at recommended bias voltages
Device Gain PDE (yellow) Dark Rate
Nom. Meas. Nom. Meas. Nom. Meas.
SSPM-050701GR-TO18 [1] 0.8×106 1.1×106 ~29% ~30% 10 MHz 9.8 MHz
SSPM-0606BG4-PCB [2] 1.5×105 2.5×105 27% 20-23% 15 MHz 8.9 MHz



SSPM06 DarkRateVsVb.png SSPM06 DarkRateVsT.png
Dark rate plotted as a function of bias voltage at extreme and room temperatures and as a function of temperature at different bias voltages. Note the disappearance of temperature dependence at low bias voltage.


SSPM06 GainVsVb.png SSPM06 GainVsT.png
SiPM gain plotted as a function of bias voltage at extreme and room temperatures and as a function of temperature at different bias voltages.


SSPM06 PDEVsVb.png SSPM06 PDEVsT.png
Photon detection efficiency as a function of bias voltage at extreme and room temperatures and as a function of temperature at different bias voltages.

Links



Written and last edited by Igor Senderovich 23:47, 8 August 2007 (EDT)