Microscope Electronics

From UConn PAN
Revision as of 22:43, 30 January 2018 by Jonesrt (talk | contribs) (→‎Digital Control Board)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Electronics

The GlueX experiment will use a 9 GeV linearly polarized photon beam to search for mesons with gluonic excitations, and measure their spectrum and couplings. To create a well-collimated photon beam, the 12 GeV electron beam from CEBAF will pass through a 20um thick diamond wafer and undergo coherent bremsstrahlung. In order to know the energy of the photon the post-bremsstrahlung electron energy must be measured. A magnet is used to spatially separate the electrons corresponding to their energy which are incident on scintillating fibers. These fibers are located to provide 4 MeV energy resolution and propagate the signal to Silicon Photomultiplier (SiPM) counters that are mounted on custom high speed circuit boards. The scintillating fibers and electronics are housed in a light-sealed enclosure called the Tagger Microscope, which the research group at the University of Connecticut have designed to measure the post-bremsstrahlung electron energy, and therefore, the emitted photon energy.


Preamplifier

The purpose of the preamplifier is to receive signals from the scintillating fibers on the SiPMs and amplify the signal. These boards have two stages, the amplifying and summing circuits. In the first amplifying circuit the 15 SiPMs are individually amplified and can be independently readout. The summing circuit takes groups of 5 individual SiPM channels and sums the signals together into a summed output. This summing circuit also has the capability to change the gain of the amplified signal which allows for the study of cosmic rays and to see the dark rate of the SiPM.

[Note: Low gain mode is set to 5V and high gain mode is set to 10V]

Final Production

Preamplifier Version 2.0


Digital Control Board

The control board is designed to regulate the bias voltages for the SiPMs and to communicate via ethernet to a remote computer. It is also designed to measure the temperature of the preamplifier and adjust the gain of the summing circuit of the preamplifier.

Final Production v1

Final Production v2

Due to some DAC channels in the v1 set of boards not working properly and thus eliminating our set of spares, the control board has been remade. There were also changes to the physical v1 boards after fabrication that have been included in the schematics and pcb drawings in v2.

Backplane

The backplane is designed to be the intermediate board between the control and preamplifier boards. The preamplifier will be attached on the inside of the tagger microscope whereas the control board will be mounted outside. The backplane will allow signals to be sent between the other two boards as well as supply the power required to run all of the boards. The cable outputs for the SiPM signals are located on the backplane.

Final Production

Power Supply Requirements

We require the following voltages on the boards:

  1. +100V (range 80V - 100V) for biasing
    • 1V steps from 80V - 100V
    • typical operation at 85V
    • maximum current demand 500mA (50W power)
    • maximum ripple P-P 50mV @ f < 1kHz
    • maximum noise P-P 5mV @ 1kHz < f < 5MHz
    • maximum HF noise P-P 20mV @ f > 5MHz
    • long-term variation < ±50mV (0.05%)
  2. +6V (range 5.5V - 6.0V) for preamplifier VCC;
    • 0.01V steps from 5.5V to 6.0V
    • typical operation at 5.75V
    • maximum current 8A (50W power)
    • maximum ripple P-P 10mV @ f < 1kHz
    • maximum noise P-P 5mV @ 1kHz < f < 5MHz
    • maximum HF noise P-P 20mV @ f > 5MHz
    • long-term variation < ±10 mV
  3. +5V for cmos logic VCC
    • fixed 4.95V - 5.05V, no adjustment required
    • maximum current 3A (15W power)
  4. -5V for DAC
    • fixed -4.95V - (-5.05V), no adjustment required
    • maximum current 65mA (0.325W power)

The ripple specs for the 100V and the 6V power supplies are based on the two coupling curves shown below, for coupling from Vbias (top plot) and preamp VCC (bottom plot) into the output signal. The Vbias curve was computed assuming R18=100Ohms.

   

Power Supply Design from Fernando B.

I recommend the following implementation for the TAGM supply system:

  1. One (1) MPOD-MINI - Wiener MPOD chassis, 5U high, 4 slots
  2. One (1) MPV8008LI - LV for preamps, logic (+5V, +6V)
  3. One (1) MPV8120I - Bias supplies for SiPMs (+100V).

Each of these supplies has 8 channels and we will use 6 from each. We will design a distribution box with inputs from the above supplies and 6 outputs; 6 cable assemblies will provide the proper supply levels to the 6 backplanes of the TAGM.

The above supplies meet or exceed your spec requirements on the wiki. Please review the supply specs here and here

These implementation will cost less than $15k (chassis, modules, distribution boxes, cables, etc) and it is fully compatible, including controls, with the remaining systems in Hall D. Also note that there is a 12 week lead time so decision is urgent.

Hamamatsu MPPC SiPMs

 

Pulse Generator

Presentations

Past Work