Line 1: |
Line 1: |
| == Mounting Bracket == | | == Mounting Bracket == |
| | | |
| + | The following hardware was built in preparation for the May, 2009 CHESS run. |
| [[Image:DiaMountBracket.png|frame|Exploded view of the mounting bracket with the diamond shown suspended on stretched wires.]] | | [[Image:DiaMountBracket.png|frame|Exploded view of the mounting bracket with the diamond shown suspended on stretched wires.]] |
| | | |
Line 43: |
Line 44: |
| |- align="center" valign="top" | | |- align="center" valign="top" |
| | [[Image:WireStretchTests.jpg|thumb|200px|Figure 1. Simple setup for testing wire stretching. Cap head bolts take the place of precise diameter rods that specify wire spacing. The ~5 g weight is shown on the right.]] | | | [[Image:WireStretchTests.jpg|thumb|200px|Figure 1. Simple setup for testing wire stretching. Cap head bolts take the place of precise diameter rods that specify wire spacing. The ~5 g weight is shown on the right.]] |
− | || [[Image:MBWireMarks.jpg|thumb|200px|Figure 2. Photo of a groove embossed by the clamped tungsten wire. (Numbers indicate mm markings)]] | + | || [[Image:MBWireMarks.jpg|thumb|250px|Figure 2. Photo of a groove embossed by the clamped tungsten wire. (Numbers indicate mm markings)]] |
| |} | | |} |
| | | |
Line 58: |
Line 59: |
| |- align="center" valign="top" | | |- align="center" valign="top" |
| | [[Image:DiaSize.jpg|200px|thumb|Figure 4. Photo of the diamond with a mm scale. It appears to be fairly precisely 4 mm]] | | | [[Image:DiaSize.jpg|200px|thumb|Figure 4. Photo of the diamond with a mm scale. It appears to be fairly precisely 4 mm]] |
− | || [[Image:Wires_6-32.jpg|200px|thumb|Figure 5. Trial of stretching wires spaced by the shank of a 6-32 screw. The resulting spacing of 3.5 mm is just a little too narrow for our 4 mm diamond.]] | + | || [[Image:Wires_6-32.jpg|250px|thumb|Figure 5. Trial of stretching wires spaced by the shank of a 6-32 screw. The resulting spacing of 3.5 mm is just a little too narrow for our 4 mm diamond.]] |
| |} | | |} |
| | | |
Line 67: |
Line 68: |
| | [[Image:DiaGlued.jpg|thumb|250px|Figure 6. The photo shows the diamond glued to 20 μm wires spaced by the minor diameter of 10-32 screws.]] | | | [[Image:DiaGlued.jpg|thumb|250px|Figure 6. The photo shows the diamond glued to 20 μm wires spaced by the minor diameter of 10-32 screws.]] |
| || | | || |
− | | [[Image:Dia_Yboundary.jpg|thumb|220px|Figure 7. A strange artifact, potentially challenging the notion that this is a mono-crystal. A slightly different lighting angle shows very flat surfaces (so these are not likely surface features.)]] | + | | [[Image:Dia_Yboundary.jpg|thumb|220px|Figure 7. A strange artifact, potentially challenging the notion that this is a mono-crystal. A slightly different lighting angle shows very flat surfaces (so these are not likely surface features.) Photo orientation: left is the direction of the goniometer mounting rod.]] |
| |} | | |} |
| | | |
Line 90: |
Line 91: |
| * twist ties | | * twist ties |
| * ''recommended'': vice, 2" mouth minimum | | * ''recommended'': vice, 2" mouth minimum |
| + | |
| + | == References == |
| + | |
| + | * [http://www.xhuber.de/en/Products/diffractometers/xray/single_crystal/5020/5020.rsys Diffractometer at CHESS] |
| + | * [http://zeus.phys.uconn.edu/~senderovich/GlueX/Diamonds/MountingBracket/DiaMountBracket_Shaft.pdf Diamond mount support post] |