Difference between revisions of "Fiber Dimension Statistics"

From UConn PAN
Jump to navigation Jump to search
m ("who's" to "whose")
 
(20 intermediate revisions by one other user not shown)
Line 1: Line 1:
This page was created by Andrew Sampino who's logbook for spring 2016 can be found [https://docs.google.com/document/d/1esm2oDkirx5xdNzi01ZnM90xiaqDG6ZR3QxKgdmsDwk/edit#heading=h.kpi595uyjsdi here]
+
This page was created by Andrew Sampino, whose logbook for spring 2016 can be found [https://docs.google.com/document/d/1esm2oDkirx5xdNzi01ZnM90xiaqDG6ZR3QxKgdmsDwk/edit#heading=h.kpi595uyjsdi here]
  
The raw data for all of the reported statistics on this page can be found in [https://docs.google.com/spreadsheets/d/1AZPVzbwDgBWl5UXUVSnz_8_0yO6rmNUTt_MeylHasTQ/edit?pref=2&pli=1#gid=0 this] spreadsheet.
+
The raw data for all of the reported statistics on this page can be found in [https://docs.google.com/spreadsheets/d/1AZPVzbwDgBWl5UXUVSnz_8_0yO6rmNUTt_MeylHasTQ/edit?pref=2&pli=1#gid=0 this] spreadsheet. All reported values on this page are based off of "average" widths, which is the average of the two side lengths of the cross sectional square of the fibers.
  
 
==Average Width of Fibers==   
 
==Average Width of Fibers==   
 +
 +
===Average Width Along Whole Fiber===
  
 
An analysis on the average width of the fibers was performed to check how many were over the maximum desired average width (2.03mm). The width of each fiber was measured at fifteen different points as a part of the cutting process. Histogram A shows the spread of average fiber width; almost all fibers meet the width specification with less than five percent exceeding the threshold width (2.03mm).
 
An analysis on the average width of the fibers was performed to check how many were over the maximum desired average width (2.03mm). The width of each fiber was measured at fifteen different points as a part of the cutting process. Histogram A shows the spread of average fiber width; almost all fibers meet the width specification with less than five percent exceeding the threshold width (2.03mm).
Line 9: Line 11:
 
In order to gauge how accurately the averages represented the fibers, the standard deviations of the widths were also plotted. On histogram B the distribution of the standard deviation of width of each fiber is shown. Over ninety percent of the fibers' widths deviate by less than .03mm on average (1.5% of the maximum desired width). Considering histograms A and B, there are very few fibers that are too large or uneven to use.
 
In order to gauge how accurately the averages represented the fibers, the standard deviations of the widths were also plotted. On histogram B the distribution of the standard deviation of width of each fiber is shown. Over ninety percent of the fibers' widths deviate by less than .03mm on average (1.5% of the maximum desired width). Considering histograms A and B, there are very few fibers that are too large or uneven to use.
 
[[File:Dev Along Fibers.png|600px|thumb|center|Histogram B: Standard deviation of width along all fibers.]]
 
[[File:Dev Along Fibers.png|600px|thumb|center|Histogram B: Standard deviation of width along all fibers.]]
 +
 +
===Chimney End Measurements===
 +
 +
The chimney end of the fibers is the most downstream end (away from fuse, near rubber band identifiers) where the fiber is inserted in a "chimney" used to hold it in place above a silicon photomultiplier for light collection. The chimneys have a maximum width requirement of 2.03mm. One hundred and twelve fibers, shown in [https://docs.google.com/spreadsheets/d/1nNwGV8ktyOAOx1IHW56j6FE3KqDbFEpy6meRJBFwvFY/edit#gid=0 this] spreadsheet, have had their chimney ends measured as a part of an effort to produce bundles with a number of ideal dimensions for easy microscope installation. Of the one hundred and twelve measured, five fibers were found to have chimney ends that are too big. If it is assumed these fibers constitute a representative sample of all three hundred and sixty fibers, it is expected that a total of about fifteen fibers have chimney ends that are too large.
  
 
==Comparison Among Spools==
 
==Comparison Among Spools==
 
[[File:S1 Ave Spread.png|400px|thumb|right|Histogram C: S1 Average Width Spread.]]  [[File:A2 Ave Spread.png|400px|thumb|right|Histogram E: A2 Average Width Spread.]] [[File:S2 Ave Spread.png|450px|thumb|left|Histogram D: S2 Average Width Spread.]]
 
[[File:S1 Ave Spread.png|400px|thumb|right|Histogram C: S1 Average Width Spread.]]  [[File:A2 Ave Spread.png|400px|thumb|right|Histogram E: A2 Average Width Spread.]] [[File:S2 Ave Spread.png|450px|thumb|left|Histogram D: S2 Average Width Spread.]]
 
Every fiber was cut from one of four spools delivered by the manufacturer. An analysis of the widths of fibers from each spool was performed to determine if a significant difference in quality of fiber exists between them. The spools are named "A1", "A2", "S1", and "S2", where only six fibers were cut from spool A1 so it was omitted from the analysis due to a lack of representative data. As can be seen from histograms C through E, the average widths are within .025mm of each other indicating a consistent fiber size across spools. The standard deviation of spool S2 is about one and a half times as large as the other two showing substantially more change in the average width along fibers. This difference is still only on the order .01mm so no spool can be said to be significantly better or worse than the rest.
 
Every fiber was cut from one of four spools delivered by the manufacturer. An analysis of the widths of fibers from each spool was performed to determine if a significant difference in quality of fiber exists between them. The spools are named "A1", "A2", "S1", and "S2", where only six fibers were cut from spool A1 so it was omitted from the analysis due to a lack of representative data. As can be seen from histograms C through E, the average widths are within .025mm of each other indicating a consistent fiber size across spools. The standard deviation of spool S2 is about one and a half times as large as the other two showing substantially more change in the average width along fibers. This difference is still only on the order .01mm so no spool can be said to be significantly better or worse than the rest.
<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>
+
<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>
 
==Fuse Widths==
 
==Fuse Widths==
Fuse widths are the maximum thickness of a fiber at the fuse site between the scintillating fiber and the upstream end of the waveguide. The fusing process typically creates a slight bulge around the interface, which can interfere with bundling in the detectors. All fuse widths were measured as a part of the fusing procedure
+
Fuse widths are the maximum thickness of a fiber at the fuse site between the scintillating fiber and the upstream end of the waveguide. The fusing process typically creates a slight bulge around the interface, which can interfere with bundling in the detectors. All fuse widths were measured as a part of the fusing procedure. Histogram F shows the distribution of fuse widths among all fused fibers (321 out of 360). The fibers average a fuse width of about 2.08mm, which puts sixty one percent of the fibers (196 fibers) over the originally planned maximum width of (2.05mm). Using a more lenient maximum width of 2.15mm, only thirteen percent of fibers (43 fibers) fall out of the acceptable range. Even though many of the fibers have a large fuse joint, they shouldn't be counted as unusable since these joints can be sanded down without large losses of light yield.  [[File:Fused Spread.png|450px|thumb|right|Histogram F: Fuse Width Spread.]]

Latest revision as of 14:15, 12 July 2017

This page was created by Andrew Sampino, whose logbook for spring 2016 can be found here

The raw data for all of the reported statistics on this page can be found in this spreadsheet. All reported values on this page are based off of "average" widths, which is the average of the two side lengths of the cross sectional square of the fibers.

Average Width of Fibers

Average Width Along Whole Fiber

An analysis on the average width of the fibers was performed to check how many were over the maximum desired average width (2.03mm). The width of each fiber was measured at fifteen different points as a part of the cutting process. Histogram A shows the spread of average fiber width; almost all fibers meet the width specification with less than five percent exceeding the threshold width (2.03mm).

Histogram A: Average width of all fibers.

In order to gauge how accurately the averages represented the fibers, the standard deviations of the widths were also plotted. On histogram B the distribution of the standard deviation of width of each fiber is shown. Over ninety percent of the fibers' widths deviate by less than .03mm on average (1.5% of the maximum desired width). Considering histograms A and B, there are very few fibers that are too large or uneven to use.

Histogram B: Standard deviation of width along all fibers.

Chimney End Measurements

The chimney end of the fibers is the most downstream end (away from fuse, near rubber band identifiers) where the fiber is inserted in a "chimney" used to hold it in place above a silicon photomultiplier for light collection. The chimneys have a maximum width requirement of 2.03mm. One hundred and twelve fibers, shown in this spreadsheet, have had their chimney ends measured as a part of an effort to produce bundles with a number of ideal dimensions for easy microscope installation. Of the one hundred and twelve measured, five fibers were found to have chimney ends that are too big. If it is assumed these fibers constitute a representative sample of all three hundred and sixty fibers, it is expected that a total of about fifteen fibers have chimney ends that are too large.

Comparison Among Spools

Histogram C: S1 Average Width Spread.
Histogram E: A2 Average Width Spread.
Histogram D: S2 Average Width Spread.

Every fiber was cut from one of four spools delivered by the manufacturer. An analysis of the widths of fibers from each spool was performed to determine if a significant difference in quality of fiber exists between them. The spools are named "A1", "A2", "S1", and "S2", where only six fibers were cut from spool A1 so it was omitted from the analysis due to a lack of representative data. As can be seen from histograms C through E, the average widths are within .025mm of each other indicating a consistent fiber size across spools. The standard deviation of spool S2 is about one and a half times as large as the other two showing substantially more change in the average width along fibers. This difference is still only on the order .01mm so no spool can be said to be significantly better or worse than the rest.















Fuse Widths

Fuse widths are the maximum thickness of a fiber at the fuse site between the scintillating fiber and the upstream end of the waveguide. The fusing process typically creates a slight bulge around the interface, which can interfere with bundling in the detectors. All fuse widths were measured as a part of the fusing procedure. Histogram F shows the distribution of fuse widths among all fused fibers (321 out of 360). The fibers average a fuse width of about 2.08mm, which puts sixty one percent of the fibers (196 fibers) over the originally planned maximum width of (2.05mm). Using a more lenient maximum width of 2.15mm, only thirteen percent of fibers (43 fibers) fall out of the acceptable range. Even though many of the fibers have a large fuse joint, they shouldn't be counted as unusable since these joints can be sanded down without large losses of light yield.

Histogram F: Fuse Width Spread.