BW July 2018 - Revision history

Bwillis at 22:31, 30 July 2018

2018-07-30T22:31:33Z

Bwillis at 19:41, 25 July 2018

2018-07-25T19:41:38Z

Bwillis at 17:30, 24 July 2018

2018-07-24T17:30:55Z

Bwillis at 16:56, 24 July 2018

2018-07-24T16:56:36Z

Bwillis at 20:52, 20 July 2018

2018-07-20T20:52:18Z

Bwillis at 15:46, 19 July 2018

2018-07-19T15:46:04Z

Bwillis at 21:11, 18 July 2018

2018-07-18T21:11:44Z

Bwillis: Created page with "7/13: Yesterday I did some practice fuses and then fused four productions fibers in bundle 404 using a piece of sponge gasket to keep the clamps from bottoming out. The work w..."

2018-07-13T20:13:09Z

Created page with "7/13: Yesterday I did some practice fuses and then fused four productions fibers in bundle 404 using a piece of sponge gasket to keep the clamps from bottoming out. The work w..."

New page

7/13: Yesterday I did some practice fuses and then fused four productions fibers in bundle 404 using a piece of sponge gasket to keep the clamps from bottoming out. The work was slow because it took me a long time to remove wings.

Today Jim said Andrew was getting very good results from fusing. He suggested that Andrew should take over as primary fusing technician. That may be a good idea since Andrew seems to be quicker at removing wings.

While Andrew was learning to fuse scrap fibers with the sponge gasket, I cut more short fibers. Later I cleaned a bundle of shorts scraps and started polishing a new one.

← Older revision		Revision as of 22:31, 30 July 2018
Line 16:		Line 16:

	7/25: Because the tests on bundle 401 after fusing were significantly lower than before fusing, I inspected the fibers whose transmission dropped the most. I did not see any signs of damage or poor fuse quality, however.		7/25: Because the tests on bundle 401 after fusing were significantly lower than before fusing, I inspected the fibers whose transmission dropped the most. I did not see any signs of damage or poor fuse quality, however.
		+
		+	7/30: For answering the questions from Richard and Jim, see the All Tests sheet in 401 Stage 2 Tests 1.

← Older revision		Revision as of 19:41, 25 July 2018
Line 14:		Line 14:

	When I put bundle 401 in the dark box, I noticed a strip of paper between the fibers and the Kapton. That might have affected the width measurements.		When I put bundle 401 in the dark box, I noticed a strip of paper between the fibers and the Kapton. That might have affected the width measurements.
		+
		+	7/25: Because the tests on bundle 401 after fusing were significantly lower than before fusing, I inspected the fibers whose transmission dropped the most. I did not see any signs of damage or poor fuse quality, however.

← Older revision		Revision as of 17:30, 24 July 2018
Line 12:		Line 12:

	7/24: I measured bundle 401 on the popsicle stick. Bundle positions 16 to 30 are 6.81 mm wide including the Kapton. Measuring at positions 1 to 15, the bundle is 12.43 mm wide including the Kapton. The bundle is around 10 mm high, as it should be.		7/24: I measured bundle 401 on the popsicle stick. Bundle positions 16 to 30 are 6.81 mm wide including the Kapton. Measuring at positions 1 to 15, the bundle is 12.43 mm wide including the Kapton. The bundle is around 10 mm high, as it should be.
		+
		+	When I put bundle 401 in the dark box, I noticed a strip of paper between the fibers and the Kapton. That might have affected the width measurements.

← Older revision		Revision as of 16:56, 24 July 2018
Line 10:		Line 10:

	7/20: On Monday I need to put the bundle 404 tests in the testing logbook. They should go there as well as in my spreadsheet.		7/20: On Monday I need to put the bundle 404 tests in the testing logbook. They should go there as well as in my spreadsheet.
		+
		+	7/24: I measured bundle 401 on the popsicle stick. Bundle positions 16 to 30 are 6.81 mm wide including the Kapton. Measuring at positions 1 to 15, the bundle is 12.43 mm wide including the Kapton. The bundle is around 10 mm high, as it should be.

← Older revision		Revision as of 20:52, 20 July 2018
Line 8:		Line 8:

	7/19: Sci-Fi bundle 6 was left out of the storage box overnight one night this week. We need to avoid repeating this mistake.		7/19: Sci-Fi bundle 6 was left out of the storage box overnight one night this week. We need to avoid repeating this mistake.
		+
		+	7/20: On Monday I need to put the bundle 404 tests in the testing logbook. They should go there as well as in my spreadsheet.

← Older revision		Revision as of 15:46, 19 July 2018
Line 6:		Line 6:

	7/18: The piece of sponge gasket for gripping fibers was missing today. I may have lost it while cleaning up the fusing work station today. Andrew made a new one.		7/18: The piece of sponge gasket for gripping fibers was missing today. I may have lost it while cleaning up the fusing work station today. Andrew made a new one.
		+
		+	7/19: Sci-Fi bundle 6 was left out of the storage box overnight one night this week. We need to avoid repeating this mistake.

← Older revision		Revision as of 21:11, 18 July 2018
Line 4:		Line 4:

	While Andrew was learning to fuse scrap fibers with the sponge gasket, I cut more short fibers. Later I cleaned a bundle of shorts scraps and started polishing a new one.		While Andrew was learning to fuse scrap fibers with the sponge gasket, I cut more short fibers. Later I cleaned a bundle of shorts scraps and started polishing a new one.
		+
		+	7/18: The piece of sponge gasket for gripping fibers was missing today. I may have lost it while cleaning up the fusing work station today. Andrew made a new one.